6 Steps To Replace The Micro Switch In Mouse
6 Steps to Replace the Micro Switch in Mouse
1. First, unscrew the bottom screw of the mouse, open the mouse shell, and take out the PCB circuit board.
2. Prepare the soldering iron. The temperature of the soldering iron should be controlled below 300 degrees. After the solder melts, the soldering iron should be separated from the solder joint as quickly as possible to prevent damage to the PCB caused by high temperature.
3. The micro switch has three pins(terminaler), and the solder can be easily removed by removing the solder on the pin. Use the suction gun: The soldering iron is close to the solder joint. After the solder melts, the gun head is sucked into the solder joint as a whole. This effect is the best and can be cleaned with just one click.
4. After removing the old micro switch, clean the solder residue on the PCB solder joints to easily install the new micro switch. Note that the direction of the fretting electric shock is marked on the PCB, so don’t install the wrong direction of the fretting.
5. After the microswitch is fully pressed on the protection board, the tin is repaired without too much solder, but it must be uniform, and there can be no continuous welding.
6. Finally, put the PCB back into the bottom case of the mouse, and the mouse is assembled, and you’re done.
What Is A Mouse Micro Switch
A mouse micro switch is a micro switch inside the mouse. The micro switch is part of a minor component and has mechanical and electrical functionality. Only when you press your mouse will the microswitch run.
The mouse micro switch controls the circuit open or close. The mini bounce travel makes the click of the mouse more sensitive.
Mouse Micro Switch Work Principle
The clicking number will reach over 5 thousand clicks when using a mouse. It means the micro switch will activate more than 5 thousand cycles. Generally speaking, the Unionwell microswitch has 1,000,000 cycles of mechanical service life. You can choose the Unionwell microswitch without worry. High-quality and High-reliability microswitch!
How To Adjust The Feeling Of Mouse Micro Switch?
If you want to adjust the feeling of the mouse micro switch, you should get learning: Most of the weight and noise that mouse switches create come from the overall design of the mouse and the mouse housing.
As a mouse manufacturer, adjusting the mouse housing and mouse micro switch. EN “klikkende” sound may be the key to success!
Best Mouse Micro Switch From Unionwell Micro Switch Manufacturer
As we know, Unionwell G10 series micro switches are likely the most common replacement, and for a good reason. They’re on the heavier side of buttons but extremely snappy and consistent. We would say that these fall between Omron( D2FC-F-7N) and Huang regarding the required force for clicking.
Unionwell G10 Series Subminiature Micro Switch Products List >>
Huizhou Unionwell Sensing & Control Electronics Co., Ltd spesialiserer seg på kvalitetsmikrobrytere for bilindustrien og hvitevarer av hvitevarer. Hovedprodukter inkluderer grunnleggende mikrobrytere, vanntette brytere, lufttrykkbrytere, mekaniske tastaturbrytere, dørbrytere, etc.
For bedre prisgaranti, ledetid, og kvalitetskontroll, vi acquired Huizhou Greetech Electronics Co., Ltd i 2021. Vi gjorde det til vår produksjonsbase i Kina med over 1000 ansatte og 260 millioner stykker/år produksjonskapasitet.
Huizhou Greetech is an ISO9001, IATF16949 and ISO14001 certified micro switch manufacturer whose complete series of products have been granted global access permit certifications, including ENEC, UL, CE, CB, etc.
De fleste av våre forretningspartnere/sluttkunder er globale 500 bedrifter, inkludert verdenskjente merkevarer for husholdningsapparater og ledende billeverandører i Nord-Amerika og Europa.
A one-stop system vil dekke produktutvikling, presisjonsstøping, sprøytestøping, presisjonsstempling, automatisert utstyr R&D, montering, og testing.
Det profesjonelle salgsteamet er tilgjengelig for å gi hjelp og rask respons på 3D-tegningsforespørsler, pristilbud, og tilgang til et tilstrekkelig eksempelprogram som lar ingeniører teste og kvalifisere brytere for deres sluttproduktapplikasjoner.
Core Value:
Goal, Responsibility, Coordination, Innovation
Effort, Development, Openness, Integrity
Our Mission:
We are obligated to maintain long-term relationships that stand the test of time.
Our Vision:
To become a first-class global manufacturer of precision components and modules.
Unionwell switches manufacture various micro switches, subminiatyr mikrobrytere, basic switch, forseglede mikrobrytere, etc., and has a one-stop R & D and production system.
Related articles:
Micro Switch in Computer Mouse
Miniature Snap Action Switch for Mouse
